Kadran Selamlama

1.STG 17 (dash panel insert)
2.STG adjustment -> function 10
3.Staging / staging aktive edin

 

XDS(Elektronik Diferansiyel Kilidi) Aktifleştirme

1.STG 03 (brake)
2.STG Lange Coding -> Function 07
3.Byte 17
4.Bit 3 seçin

 

Cama Su Püskürtüldükten sonra Sileceklerin 2 Saniye Sonra 1 Kez daha Çalışması

1.STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 1
4.Bit 3 aktifleştirin
5.Byte 21
6.Bit 4 aktifleştirin

 

Gündüz Farlarının Parlaklığını/Işık Şiddetini Ayarlama

2011 yılına kadar olan araçlarda

1.STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 8 / 1A = 25%
Byte 8/32 = 50%
Byte 8 / 3C = 60%
Byte 8 / 4B = 75%
Byte 8/00 = 92% varsayılan
Byte 8/64 = 100%

2012 yılından sonraki araçlar

1.STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 24 / 1A = 25%
Byte 24/32 = 50%
Byte 24 / 3C = 60%
Byte 24 / 4B = 75%
Byte 24/00 = 92% varsayılan değer
Byte 24/64 = 100%

 

Gündüz Sürüş Farlarını Özelleştirme:

1.STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 15 Bit 6 (TFL separate lights – LED)
Byte 24 Bit 7 (TFL as a position light)
Byte 27 Bit 2 (TFL as a sidelight – is dimmed when low beam)
Byte 18 to 04 HEX

 

Geri Viteste Sağ Aynanın Aşağı İnmesi:

1.STG 52 (Türelektr. Beifahr)
2.STG coding -> function 07
3.Byte 4
4.Bit 2 ve 3 ü aktifleştirin

 

Far Yıkama Sisteminin Ayarlanması:

1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 20
4.Disable Bit 5
More customization options regarding headlamp cleaning system.:
Headlight washers (SWRA) adapt Ansteuerverzögerungszeit:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 05
4.Adjust accordingly delay time. (Resolution 50 ms)
Headlight washers (SWRA) adjust driving time:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 06
4.Adjust accordingly delay time. (Resolution 50 ms)

 

“Rain Close” Aktifleştirme (Yağmur Yağdığında camlar ve açılır tavanın otomatik kapanması)

1.STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 4
4.Bit 5 ve 6 yı aktifleştirin
5.STG 09 (vehicle power)
6.STG long coding -> function 07
 Rain ve light sensor seçin – RLS
7.Byte 0
8.Bit 2 yi aktifleştirin

 

Sis Lambalarını Gündüz Farı Gibi Kullanma:

In the central electrics You have the option at the Skoda Superb 3T to activate the fog lights as daytime running lights
The following code is to be applied:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 14
4.Enable Bit 1
More customization options regarding daytime running lights.:
Daytime running light inactive when the handbrake
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 11
4.Enable Bit 0

Daytime running active only in light switch position AUTO:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 26
4.Enable Bit 4

Daytime running tale available:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 26
4.Enable Bit 5

 

Tek Dokunuş Sinyal Sayısını Değiştirme

In the central electrics You have the option at the Skoda Superb 3T adjust the Zylkus of comfort blinker. Value range 1-5 possible (ie between 1x or 5x flashes per tap)
The following code is to be applied:
1.Select STG 09 (vehicle power)
2.STG adjustment -> function 10
3.Channel 13
4.Adjust Value: 1-5 Value 3 (standard – 3x blinking)

Ani Frende Dörtlülerin de Yanması:

In the network control unit gives you the option when Skoda Superb 3T Notbremsblinken the property via Blink – and brake lights (Adaptive Brake Light) activate
The following code is to be applied:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 16
4.Enable Bit 1
5.Bit 2 Activate additionally possible: even when towing a trailer possible
6.Byte 23
7.Enable Bit 5

 

Emniyet Kemeri Uyarısı

In the dash panel insert (KI) gives you the option when Skoda Superb 3T deactivate the seat belt reminders

The following code is to be applied:

1.Select STG 17 (dash panel insert)
2.STG Lange Coding -> Function 07
3.Byte 1
4.Disable Bit 1

Yokuş Kalkış Desteği’nin Süresini Ayarlama:

In braking and ABS control unit gives you the option when Skoda Superb 3T adjust the function of the Hill Hold Assistant (Hill Start Assistant)

Coding:

1.Select STG 03 (brake / ABS)
2.STG adjustment -> function 10
3.Select Berganfahrhilfe or channel 58
4.Fit Function:
0 = Berganfahrhilfe “normal”
1 = Berganfahrhilfe “early” (starting at low speed)
2 = Berganfahrhilfe “late” (starting at a higher speed and a slipping clutch) <- for example, towing

 

Emniyet Kemeri Uyarısı

1.STG 17 (dash panel insert)
2.STG Lange Coding -> Function 07
3.Byte 1
4.Bit 1 pasifleştirin

Yokuş Kalkış Desteği’nin Süresini Ayarlama:

1.STG 03 (brake / ABS)
2.STG adjustment -> function 10
3.Select Berganfahrhilfe or channel 58
4.Fit Function:
0 = Berganfahrhilfe “normal”
1 = Berganfahrhilfe “early” (starting at low speed)
2 = Berganfahrhilfe “late” (starting at a higher speed and a slipping clutch) <- for example, towing

 

Yüksek süratlerde farlar için otoban modunu aktifleştirmek:

In the network control unit gives you the option when Skoda Superb 3T activate the motorway light. At high speed, then the illumination of xenon is adjusted automatically – the light cone is narrower in width and thus longer.
Motorway mode uses the large amount of light and optimized side and ground lights of the xenon plus pig launcher. Using sensors, a vehicle electronic system continuously analyzes the speed of the vehicle. After a short time above 110 km / h the system is based on highway driving and automatically switches from low beam mode in motorway light mode. The special position of the diaphragm in the xenon plus headlights additional light will be focused by an aluminum reflector and thrown far ahead of the vehicle without dazzling other road users, however. The sight is more than doubled: from 70m in low beam mode at 150m motorway light mode. This increase in the visibility means at a speed of 130 km / h has a gain of 2 seconds to react to objects in front of the vehicle can. Motorway mode thus increases driving safety significantly.
The following code is to be applied:
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Subsystem: Rain / Light Sensor
4.Byte 02:
+01 For motorway light
+02 for rain light (if both are required thus: 03 as HEX entry)

-Otomatik Kilitleme ve Kilit Açma:
In the central electrics You have the option at the VW Golf VI, the automatic locking and unlocking of the car to activate or deactivate

The following code is to be applied:

1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 0
4.Bit 1 (Auto-Unlock)
5.Bit 2 (Auto-Lock)

Fren Yardımcısını Ayarlamak:

In the braking electronics gives you the option when Skoda Superb 3T adjust the brake assist. Thus, the response of the brake pedal changes. (delayed faster)

The following code is to be applied:

1.Select STG 03 (brake electronics)
2.STG adjustment -> function 10
3.Channel 9
4.Value 2 change (default: 0)

Gündüz farlarını kapatmak:

In the central electrics You have the option at the Skoda Superb 3T turn off or disable the default daytime running lights

The following code is to be applied:

1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 11
4.Disable Bit 2

 

Aracı kilitlerken kornanın çalması:

In the central electrics You have the option at the Skoda Superb 3T the DWA to acknowledge (alarm system) when unlocking and locking the vehicle with the horn (so-called US -. Style)

The following code is to be applied:

1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 5
4.Enable Bit 1
5.Enable Bit 4
: additionally possible to make DWA acknowledgment in the comfort menu visible
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 5
4.Disable Bit 2
Adaptation of DWA:
1.Select STG 09 (vehicle power)
2.STG adjustment -> function 10
3.Channel 3
4.Value set in accordance with 0 = frequency modulated alarm signal 10 Tamperalarme (USA 5min) 1 = intermittent alarm signal 10 Tamperalarme (EU, 5min) 2 = frequency modulated alarm signal 1 tamper alarm (USA, 30s) 3 = intermittent alarm signal 1 tamper alarm (EU, 30s)

Köşe dönüş farlarını aktive etmek:

In the central electrics You have the option at the Skoda Superb 3T to activate the cornering light. It is then driven through the fog lights.

The following code is to be applied:

1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 14
4.Enable Bit 7
additionally possible: limit cornering time
1.Select STG 09 (vehicle power)
2.STG Lange Coding -> Function 07
3.Byte 12
4.Enable Bit 4

 

Columbus’ta hareket halinde video izlemek:

1.Ignition and engine on
2.Insert DVD and start the desired movie
3.On the steering wheel, press the voice button (who has no MFL, pressed a pinch the small “i” button on the top right of the speaker icon at the RNS) -> 3-tone chime sounds
4.Immediately on the RNS 510 “TONE” button (bottom left) -> Gong and another signal sounded together
5.The frame of the movie will freeze briefly and plays after half a second further
6.Start driving!
DANGER
§When changing the radio mode – whether via button or voice command (NAV, MAP, …) this activation is automatic, so disabled will be reset to the original setting!
§To reactivate the vehicle must again resting (so think twice before)!
§Navigation and DVD-activation function together perfectly and without sacrificing speed, normally plan a route just before this intervention and start route guidance!
§The activation has on all other controls and displays in the MFA + no influence!
Function depends on the firmware version of RNS510. Works for 2660 and 2680

Columbus Gizli Menüyü Açmak:

In the navigation control unit gives you the option when Skoda Superb 3T unlock the hidden menu of RNA 510th

The following code is to be applied:

1.Select STG 37 (navigation)
2.STG adjustment -> function 10
3.Channel Number 50
4.New to this set: 1
5.RNS reset
6.The hidden menu can be opened with the key combination Setup (hold very long pressed -> see also video)